It is manually or electrically operated, allowing a person to work with their bare hands on a physical system It consists of screwdrivers, pliers, cutters, and other tools., Cleaning tool, Diagnostic tool, ESD tool, Hand tool, Darwin is about to make LAN Cable with RJ-45 for his computer connectors. Which tool is used to attach connectors to wires?, Crimper, Hex Driver, Part Retriever, Punch down, Which of the following is used to retrieve and place small parts that are hard to reach with your finger?, Crimper, Phillip head screwdriver, Hex Driver, Tweezer, Why is it important to use safe hand tools?, For effective use, For efficient use, For safety purposes, To complete your work accurately, Which of the following are NOT the common hazards, misuse, and improper maintenance associated with the use of hand tools?, Broken wooden handles that cause the head of the tool to fly off or mushroomed heads that can break upon impact., Rusty pliers are used as a hammer, Use a specific type of screwdriver depending on the size and slot of the screws., Using a non-sparkling device in the presence of flammable vapors and dust in an open space area for safety reasons., Which of the following screwdrivers is used to loosen or tighten slotted screws?, Flat head screwdriver, Phillip head screwdriver, Hex Driver, Hex DriverTorx screwdriver, Faulty or Unsafe hand tools can cause lot of injuries. In using the screwdrivers, they are dos and don’ts that we need to follow. Which of the following is the appropriate way of using SCREWDRIVERS?, Always use a screwdriver handle that best fits the screw slot properly., Keep the screwdrivers with damaged or rusty handles., Never use a screwdriver as a pry bar, a chisel, a punch stirrer, or a scraper., Use pliers on the screwdriver for additional leverage., Being organized and placing things in their proper places are crucial since proper tool storage is highly important. Which of the following describes how to store tools properly?, Avoid stacking tools on top of each other, Dump all your tools into one toolbox, Expose your tools to rain., Leave your tools laying on the ground., Utility knives and blades are hand tools that help our work simpler and easier. The following are the proper use of utility knives and blades, which of them is NOT an appropriate way of using it?, Don’t leave the knife unattended with the blade exposed., Don’t replace the blade when the blade starts to "tear" instead of cutting., Don’t bend or apply side loads to blades by using them to open cans or pay loose objects., Keep your free hand away from the cutting line, Josh is disassembling the system unit, and while removing the screws from the hard disk drive, he noticed that the screwdriver that he is using is magnetized. What is most likely to happen when we use a magnetized screwdriver?, A magnetized tool will help you to make your work productive, A magnetized tool can strip the screw and it will damage the screw head., A magnetized tool is an extra advantage in making a pilot hole before you push the screw in., A magnetized tool has magnetic field that can be harmful to the data stored in magnetic media., Garcia is working on his computer system unit, but some parts are difficult to reach with his fingertips. Which of the following sets of hand tools should he use to retrieve and position pieces that may be difficult to pick with his fingertips?, Phillips head Screwdriver, Flat head screwdriver and Torx Screwdriver, Needle nose plier, part retriever and tweezers, Wire cutter, needle nose plier, and hex driver, Crimper, Punch down tool, and wire cutte, Kevin, a computer technician, is about to do some repairs on his computer system unit. Before touching any internal electronic components, he is touching a metal grounded object (such as an unpainted metal surface on your computer’s Input/Output panel). What safety precautions did he follow?, Discharging static electricity, Re-aligning Input/Output panel, Re-aligning twisted pins., Grounding magnetized hand tools., There is a right tool for every job. As a computer technician, what skill do you think will help you to prevent accidents and harm to the equipment and people?, Proper lubrication of hand tools., Proper use of tools., Proper ways of cleaning and sorting, Proper ways of storing hand tools., In implementing the Occupational Health and Safety Standards you need to observe the health, safety, and welfare of all people at the workplace. Which of the following situations is a BEST practice of common Occupational health and safety standards?, Be cautious with tools that can cause short circuits, Hold the components on the edges and touch the part of the Integrated-Circuit (IC)., Make sure that the pins are dislocated., Use excessive force if things don't slip into place., What is a process that removes unwanted substances, such as dirt, infectious agents and other impurities, from the object or the environment?, Cleaning, Lubrication, Sharpening, Storing, What type of lubrication is used in a cross-section between boundary and hydrodynamic?, Boundary Lubrication, Electrohydrodynamic, Full-film, Mixed Lubrication, 5S is a method of organization in the workplace that uses a list of five Japanese words. Which of the following refers to sorting through all items in a location and removing all unnecessary items from the location?, Sort (Seiri), Shine (Seiso), Set In Order (Seiton, Standardize (Seiketsu), This type of pliers has jaws that come to the point of firmly grasping small parts or wires, particularly in tight locations., Linesman pliers, Needle-nose pliers, Slip-joint pliers, Wire Strippers, Pliers are used to grab and hold a part. What type of pliers has two settings in the handle that allow for two widths?, Groove joint, Locking, Needle nose, Slip joint, What tools are used to link wires in such a way that they are capable of transmitting data?, Crimpers, Needle nose pliers, Torx Screwdrivers, Wire Strippers, There are different ways to store tools and equipment. Which among these terms defines the smartest solution for keeping your power tools organized, especially if the problem is space?, Cabinet, Cases, Drawers, Racks, Koby is cleaning and preparing storage for his tools. How can he keep his tools in good working condition during storage?, Clean tools after each use, Store tools near the ground, Put the tools back in storage right after use, Put lock long-handled instruments in the plastic bin., Why do you need to use dividers to isolate precision tools/instruments from each other?, To keep them dry, To reduce moisture., To avoid being magnetized., To avoid stacking on top of each other, Justine is doing his project; he wanted to join two or more conductors inside the junction box. Which type of jointing is applicable?, Britannia joint, Rat Tail or Pig Tail, Straight joint, Tee Joint/Wrapped Tap, There are useful tips for storing instruments; which of the following should NOT be considered?, Always store tools in a dry place., Make sure the location is well-protected from disruptive factors., Do not store precision instruments where they can bump into each other, Precision measuring tools should be put near any magnetic material such as a magnetic worktable., What do you call a single slender rod or filament of drawn metal?, Cable, Conductor, Current, Wire, Which type of electrical wire is composed of many thin strands of wires twisted together and can be used for longer periods?, Multi-conductor, Stranded, Solid, Twisted, Which of the following types of pliers are used to cut, bend, shape, and stretch the lead of electronics component or connecting wire?, Linesman pliers, Long nose pliers, Side cutting pliers, Stubby pliers, Gregorio wanted to buy a new set of screwdrivers for his repair shop. What kind of screwdriver does he need if he’s going to use it to drive the screws with hexagonal slot heads?, Allen or wrench, Phillips Head, Stubby, Torx, There are different parts of a multimeter. Which part is used to display visualization and consists of a five-digit display screen where one represents the sign value and the other four have a number representation?, Display screen, Ports, Probes, Selection knob, As a computer technician, how do you maintain and care for a multimeter properly?, Drop the multimeter often., Never read the manual of a multi-tester before using it., Be sure that the multi-tester is configured based on its range setting., In reading the amount of voltage always starts to the lowest range to set the tester setting., What is the process of joining two or more electronic parts, like wires or circuit boards, together by melting solder at the connection?, Clamping screw, Lubricating tools, Soldering joint, Splicing wire, What do you call a representation of the physical connections, the layout of the electrical system, or the circuit, an abstract, pictorial representation of symbols, and its schematic?, Concept Map, Electrical wiring diagram, Mind Map, Matrix or quadrant chart, Which of the following types of adjusting accessories consists of one or more "ears" or close elements?, Ear clamps, Screw clamps, Spring clamps, Wire clamps, Which type of electrical wiring diagram uses the symbol same as single line diagram that represents the power system components and additional symbols that are used in schematic and wiring diagrams?, Ladder, Pictorial, Single-line, Three-line, Who is the authorized person from the government or municipality that is responsible for inspecting electrical connections and electrical systems?, Building inspector, Electrician, Electrical inspector, Lineman, What fastening device is used to hold or secure objects tightly together to prevent movement or separation through the application of inward pressure?, Bolts, Clamps, Screws, Studs, What type of adjusting accessory is a piece of heavy wire, made of steel, bent into a tight U, next formed into a ring shape with one end overlapping the other, and lastly bent outwards and cut?, Ear clamp, Screw clamp, Spring clamp, Wire clamp, Why is it important to perform an electrical safety inspection?, It helps to save energy and reduce costs., It helps to unfit insurance risk assessment inspections requirements, It helps to ignore the outdated wiring such as aluminums or knob-and-tube., It helps to neglect the safe operation of electrical components at work or home., Which of the following options BEST describes the process of fault diagnosis, servicing, and repair of electrical components of electrical wiring and electronic circuits?, Corrective maintenance, Condition-based maintenance, Electrical maintenance, Preventive maintenance

TLE Reviewer

by
Print
Embed

Leaderboard

Visual style

Options

Switch template

Continue editing: ?