Készítsen feladatokat gyorsan, egyszerűen
Létrehozás
Bejelentkezés
Regisztráció
Magyar
Kezdőlap
Jellemzők
Díjcsomagok
Közösség
Kezdőlap
Jellemzők
Közösség
Kapcsolat
Díjcsomagok
Súgó
Bejelentkezés
Regisztráció
Nyelv
Iskolám
Saját profil
Személyes adatok szerkesztése
Nyelv és terület
Kijelentkezés
Català
Cebuano
Čeština
Dansk
Deutsch
Eesti keel
English
Español
Français
Hrvatski
Indonesia
Italiano
Latvian
Lietuvių
Magyar
Melayu
Nederlands
Norsk
Polski
Português
Română
Slovenčina
Slovenščina
Srpski
Suomi
Svenska
Tagalog
Türkçe
Vietnamese
ελληνικά
български
Қазақ
Русский
Српски
Українська
עִברִית
عربى
हिंदी
ગુજરાતી
ภาษาไทย
한국어
日本語
简体字
繁體字
The given 4-bit binary value "0100" that is used to identify an IPv4 packet., A 4-bit field in an IP header indicates the header length, with a minimum size of 20 bytes., Formally called a Type of Service (ToS) field, the DS field is an 8-bit field used to determine the priority of each packet. , The six most significant bits of the DiffServ field are the Differentiated Service Code Point (DSCP)., The last two bits are the Explicit Congestion Notification (ECN) bits., The total length field in an IP packet defines the packet size, ranging from a minimum of two bytes to a maximum of 65,535 bytes, although practical packets tend to be smaller., As an IP packet moves through the internet, it might need to cross a route that cannot handle the size of the packet. , The packet will be divided, or fragmented into smaller packets and reassembled later., These fields are used to fragment and reassemble packets., The 8-bit Time-to-Live (TTL) field in an IP packet, set by the sender, decreases at routers, and if it reaches zero, the packet is discarded, and an Internet Control Message Protocol (ICMP) Time Exceeded message is sent to the source IP., The 8-bit binary field in an IP packet specifies the next-level protocol, helping the network layer route the data to the appropriate upper-layer protocol, with common values like ICMP (1), TCP (6), and UDP (17)., A value that is calculated based on the contents of the IP header. Used to determine if any errors have been introduced during transmission., Contains a 32-bit binary value that represents the source IPv4 address of the packet. The source IPv4 address is always a unicast address., Contains a 32-bit binary value that represents the destination IPv4 address of the packet., This field in an IP packet can be of varying length, and if it's not a multiple of 32 bits, it's padded with zeros to make it a multiple of 32 bits..
14%
IPv4 Packet Header
Megosztás
szerző:
Msousa7
11th Grade
Vocational / Technical
Computing
Math
Egyebek
Tartalom szerkesztése
Nyomtatás...
Beágyazás
Hozzárendelések
Kapcsoló sablon
Az összes megjelenítése
További formátumok jelennek meg a tevékenység lejátszásakor.
Bejelentkezés szükséges
Vizuális stílus
Betűtípusok
Előfizetés szükséges
Beállítások
Ranglista
Több megjelenítése...
Részletek elrejtése
Ez a ranglista jelenleg privát. Kattintson a
Megosztás
és tegye nyílvánossá
Ezt a ranglistát a tulajdonos letiltotta
Ez a ranglista le van tiltva, mivel az opciók eltérnek a tulajdonostól.
Beállítások visszaállítása
a(z) Diagram
egy nyílt végű sablon. Nem hoz létre pontszámokat egy ranglistán.
Nyílt eredmények
Link másolása
QR-kód
Törlés
Automatikus mentés visszaállítása :
?